EA2532UA12-24.000M TR

EA2532 Series REGULATORY COMPLIANCE 2011/65 + 2015/863 191 SVHC ITEM DESCRIPTION Quartz Crystal Resonator 2.5mm x 3.2mm x 0.8mm 4 Pad Ceramic Surface Mount (SMD) ELECTRICAL SPECIFICATIONS Nominal Frequency 10MHz to 54MHz Frequency Tolerance/Stability Aging at 25°C ±50ppm at 25°C, ±100ppm over 0°C to +70°C ±50ppm at 25°C, ±100ppm over -20°C to +70°C ±50ppm at 25°C, ±100ppm over -40°C to +85°C ±50ppm at 25°C, ±100ppm over -40°C to +125°C ±30ppm at 25°C, ±50ppm over 0°C to +70°C ±30ppm at 25°C, ±50ppm over -20°C to +70°C ±30ppm at 25°C, ±50ppm over -40°C to +85°C ±30ppm at 25°C, ±50ppm over -40°C to +125°C ±15ppm at 25°C, ±30ppm over 0°C to +70°C ±15ppm at 25°C, ±30ppm over -20°C to +70°C ±15ppm at 25°C, ±30ppm over -40°C to +85°C ±15ppm at 25°C, ±20ppm over 0°C to +70°C ±15ppm at 25°C, ±20ppm over -20°C to +70°C ±15ppm at 25°C, ±20ppm over -40°C to +85°C ±10ppm at 25°C, ±15ppm over 0°C to +70°C ±10ppm at 25°C, ±15ppm over -20°C to +70°C ±10ppm at 25°C, ±15ppm over -40°C to +85°C (Only available over Nominal Frequency range of 12MHz to 54MHz) ±10ppm at 25°C, ±10ppm over 0°C to +70°C ±10ppm at 25°C, ±10ppm over -20°C to +70°C ±10ppm at 25°C, ±10ppm over -40°C to +85°C (Only available over Nominal Frequency range of 12MHz to 54MHz) ±10ppm at 25°C, ±10ppm over -30°C to +75°C (Only available over Nominal Frequency range of 20.000001MHz to 54MHz) ±3ppm/year Maximum Load Capacitance Series Resonant, 8pF Parallel Resonant to 30pF Parallel Resonant Shunt Capacitance 5pF Maximum Equivalent Series Resistance Mode of Operation 250 Ohms Maximum over Nominal Frequency of 10MHz to 11.999999MHz 150 Ohms Maximum over Nominal Frequency of 12MHz to 13.999999MHz 100 Ohms Maximum over Nominal Frequency of 14MHz to 15.999999MHz 80 Ohms Maximum over Nominal Frequency of 16MHz to 19.999999MHz 60 Ohms Maximum over Nominal Frequency of 20MHz to 29.999999MHz 50 Ohms Maximum over Nominal Frequency of 30MHz to 53.999999MHz 35 Ohms Maximum over Nominal Frequency of 54MHz to 54MHz AT-Cut Fundamental Drive Level 100µWatts Maximum Crystal Cut AT-Cut Spurious Response Measured from Fo to Fo +5000ppm -3dB Minimum -40°C to +150°C Storage Temperature Range Insulation Resistance Measured at 100Vdc 500 Megaohms Minimum Revised D: 10/27/2016 Page 2 of 10 www.ecliptek.com EA2532 Series PART NUMBERING GUIDE Revised D: 10/27/2016 Page 3 of 10 www.ecliptek.com EA2532 Series MECHANICAL DIMENSIONS SUGGESTED SOLDER PAD LAYOUT PIN 1 CONNECTION Crystal 2 Cover/Ground 3 Crystal 4 Cover/Ground All Tolerances are ±0.1 All Dimensions in Millimeters Revised D: 10/27/2016 Page 4 of 10 www.ecliptek.com EA2532 Series TAPE & REEL DIMENSIONS Quantity per Reel: 1,000 Units All Dimensions in Millimeters Compliant to EIA-481 Revised D: 10/27/2016 Page 5 of 10 www.ecliptek.com EA2532 Series RECOMMENDED SOLDER REFLOW METHODS HIGH TEMPERATURE INFRARED/CONVECTION TS MAX to TL (Ramp-up Rate) 3°C/Second Maximum Preheat - Temperature Minimum (TS MIN) - Temperature Typical (TS TYP) - Temperature Maximum(TS MAX) - Time (ts MIN) Ramp-up Rate (TL to TP) 150°C 175°C 200°C 60 - 180 Seconds Time Maintained Above: - Temperature (TL) - Time (tL) Peak Temperature (TP) 217°C 60 - 150 Seconds Target Peak Temperature(TP Target) 250°C +0/-5°C Time within 5°C of actual peak (tp) 20 - 40 Seconds Ramp-down Rate 6°C/Second Maximum Time 25°C to Peak Temperature (t) 8 Minutes Maximum Moisture Sensitivity Level Level 1 Additional Notes Temperatures shown are applied to body of device. 3°C/Second Maximum 260°C Maximum for 10 Seconds Maximum High Temperature Manual Soldering 260°C Maximum for 5 Seconds Maximum, 2 times Maximum. (Temperatures shown are applied to body of device.) Revised D: 10/27/2016 Page 6 of 10 www.ecliptek.com EA2532 Series RECOMMENDED SOLDER REFLOW METHODS LOW TEMPERATURE INFRARED/CONVECTION TS MAX to TL (Ramp-up Rate) 5°C/Second Maximum Preheat - Temperature Minimum (TS MIN) - Temperature Typical (TS TYP) - Temperature Maximum(TS MAX) - Time (tS MIN) Ramp-up Rate (TL to TP) N/A 150°C N/A 30 - 60 Seconds Time Maintained Above: - Temperature (TL) - Time (tL) Peak Temperature (TP) 150°C 200 Seconds Maximum Target Peak Temperature(TP Target) 245°C Maximum 2 Times/230˚C Maximum 1Time Time within 5°C of actual peak (tP) 10 Seconds Maximum 2 Times / 80 Seconds Maximum 1 Time Ramp-down Rate 5°C/Second Maximum Time 25°C to Peak Temperature (t) N/A Moisture Sensitivity Level Level 1 Additional Notes Temperatures shown are applied to body of device. 5°C/Second Maximum 245°C Maximum Low Temperature Manual Soldering 185°C Maximum for 10 Seconds Maximum, 2 times Maximum. (Temperatures shown are applied to body of device.) Revised D: 10/27/2016 Page 7 of 10 www.ecliptek.com